AlarmSense 2 Zone 2 Wire Fire Alarm Kit With A C-Tec Panel

Part No: CFP702-2/KIT

A 2 zone 2 wire fire alarm kit, which features the C-Tec CFP702-2 AlarmSense panel, and Apollo detectors and call points.

This kit includes the following contents:

1 x C-Tec CFP702-2 AlarmSense 2 zone panel

3 x Apollo AlarmSense optical smoke detectors with the sounder bases

1 x Apollo A1R rate of rise heat detector with sounder base

2 x Apollo AlarmSense manual call points

2 x Genesis NP Series 3.4Ah Batteries

Details of the panel below:

The C-Tec CFP702-2 two wire two zone fire alarm panel is compatible with Apollo’s Alarmsense range of fire alarm detectors, sounders, call points, and also their visual indicators.

This panel includes two AlarmSense zones, as well as four conventional sounder circuits, a class change and alert inputs; and also an on board fault and fire relays.

Specification of the AlarmSense panel:

  • Mains Supply: 230 volts 50/60Hz
  • Mains Rated Current: 350mA maximum
  • Quiescent Current: 25mA
  • 1.5A compliant integral switch mode psu
  • Stylish flush or surface mountable plastic lid and enclosure, without the need for a bezel
  • LPCB (Loss Prevention Certification Board) certified to EN54 parts 2 and 4
  • Produced in the UK by C-Tec
  • Room for two 3.2Ah VRLA batteries
  • Multiple indicators
  • System expansion connections are provided which allows for a maximum of 8 two wire repeater panels (please note that one CFP761 network card is needed for each system)
  • IP Rating: IP30
  • Weight: 1.75kg (without any batteries)

Please note that additional compatible Apollo AlarmSense detectors for these fire alarm panels can be found on this website, under the “Fire Alarm Detectors & Accessories” sub-category.

Redring 8.5kW California Shower With Multiple Right Hand Side Water And Cable Entry Points

Part no: CSA85S

Redring 8.5kW California shower, featuring the following:

  • Dual rotary controls
  • Upper control dial for selecting start/stop and also the power selection
  • Lower control dial for selecting the temperature and flow
  • Multiple right hand side water and cable entry points, to help make installation easier
  • Standard accessory kit included, which has a single mode rub clean shower head
  • 2 year guarantee

Apollo 55000-392 AlarmSense Optical Smoke Detector And Sounder

Part No: 55000-392

The AlarmSense optical smoke detector and sounder, works by the light scatter principle.

The detector will go into an alarm state, once a pre-set level of smoke has gone into the sensing chamber.

Specification:

  • Diameter: 100mm
  • Easy to install
  • Easy to extend
  • Complies with BS 5839

Quantity discounts available.

Purchase 5 or more of these AlarmSense optical smoke detectors with sounders: Price = £31.03 each +VAT.

Apollo 55000-199 AlarmSense CS Heat Detector And Sounder With Visual Indicator Base

Part No: 55000-199

The AlarmSense CS heat detector and sounder with a visual indicator base, operates once a fixed temperature has been reached.

Specification:

  • Diameter: 100mm
  • Easy to install
  • Easy to extend
  • Complies with BS 5839

Quantity discounts available.

Purchase 5 or more of these AlarmSense CS Heat Detectors With Sounder And Visual Indicator Bases: Price = £32.97 each +VAT.

Apollo 55000-198 AlarmSense A1R Heat Detector And Sounder With Visual Indicator Base

Part No: 55000-198

The AlarmSense A1R heat detector and sounder with a visual indicator base, has a fixed upper limit, and also measures the increase in temperature, known as rate of rise.

Specification:

  • Diameter: 100mm
  • Easy to install
  • Easy to extend
  • Complies with BS 5839

Quantity discounts available.

Purchase 5 or more of these AlarmSense A1R Heat Detectors With Sounder And Visual Indicator Bases: Price = £32.80 each +VAT.

Apollo 55000-395 AlarmSense Integrating Optical Smoke Detector And Sounder Beacon

Part No: 55000-395

The AlarmSense integrating optical smoke detector and sounder with a visual indicator base operates by using the light scatter principle.

The detector is able to monitor transient sources of smoke, as well as being able to discard them too.

Specification:

  • Diameter: 100mm
  • Easy to install
  • Easy to extend
  • Complies with BS 5839

Quantity discounts available.

Purchase 5 or more of these AlarmSense integrating optical smoke detector and sounder beacons: Price = £34.46 each +VAT.

CAME S9000 Surface Mounted Wireless Keypad

Part No: S9000

A surface mounted digital radio selector switch.

Specification:

  • Material: Aluminium / Steel
  • Power Supply: 1 battery (GP23A 12v dc)
  • Radio Frequency: 433.92MHz
  • Code Digits: Maximum of 8
  • Dimensions: 70 x 70 x 31mm

Apollo 55000-394 AlarmSense Optical Smoke Detector And Sounder Beacon

Part No: 55000-394

The AlarmSense optical smoke detector and sounder beacon is a combination of the 55000-390 optical smoke detector and the 45681-509 sounder beacon base unit; and this product works by the light scatter principle.

The detector will go into an alarm state, once a pre-set level of smoke has gone into the sensing chamber.

Specification:

  • Diameter: 100mm
  • Easy to install
  • Easy to extend
  • Complies with BS 5839

Quantity discounts available.

Purchase 5 or more of these AlarmSense optical smoke detector and sounder beacons: Price = £34.88 each +VAT.

C-Tec CFP761 Network Driver Card For Use With The CFP Fire Alarm Panels

Part No: CFP761

An optional device which can be used with C-Tec’s CFP standard, and also their CFP AlarmSense range of conventional fire alarm panels.

This device will allow up to 8 of the CFP760 repeater panels; and one network driver card is required per main.

Please note that the CFP760 repeater panels are supplied as standard with one of these network driver cards.

Specification:

  • Communication is carried out over a screened two-wire fire resistant cable
  • Maximum Repeater Network Cable Length: 1km
  • Power Requirements: 24v auxiliary from the host fire panel
  • Quiescent Current: 2.8mA @ 30v dc
  • Width: 30mm
  • Height: 90mm
  • Depth: 20mm
  • Weight: 0.024kg

C-Tec CFP760 8 Zone Repeater Fire Alarm Panel

Part No: CFP760

These repeater panels can be used to repeat the master CFP standard, as well as the AlarmSense 2, 4 and 8 zone fire alarm panels functions.

This is normally carried out at remote locations on a site; for example: the fire service entrances.

Specification:

  • Up to a maximum of 8 repeater panels per CFP master
  • Mains Supply: 230 volts / 50/60Hz
  • Internal Power Supply: 19 – 28.5v (nominal 27v)
  • Maximum Network Cable Length: 1km
  • Width: 380mm
  • Height: 235mm
  • Depth: 96mm
  • IP Rating: IP30
  • Maximum Battery Size: 2 x 12v 2.1Ah VRLA, which provides 72 hour standby
  • Weight Without Batteries: 1.75kg

Please note that these fire alarm panels are compatible with Apollo’s series 65 range of detectors.

Please also note that these panels require a CFP761 Network Driver Card, which is sold separately.

All of these detectors can be found under the “Fire Alarm Detectors & Accessories” sub-category on this website. This sub-category can be found under “Security & Fire Detection”

C-Tec CFP708-2 Alarmsense 8 Zone 2 Wire Fire Alarm Panel With Keypad / Keyswitch Entry

Part No: CFP708-2

The C-Tec CFP708-2 two wire eight zone fire alarm panel is compatible with Apollo’s Alarmsense range of fire alarm detectors, sounders, call points, and also their visual indicators.

This panel includes eight AlarmSense zones, as well as four conventional sounder circuits, a class change and alert inputs; and also an on board fault and fire relays.

Specification:

  • Mains Supply: 230 volts 50/60Hz
  • Mains Rated Current: 350mA maximum
  • Quiescent Current: 25mA
  • 1.5A compliant integral switch mode psu
  • Stylish flush or surface mountable plastic lid and enclosure, without the need for a bezel
  • LPCB (Loss Prevention Certification Board) certified to EN54 parts 2 and 4
  • Produced in the UK by C-Tec
  • Room for two 3.2Ah VRLA batteries
  • Multiple indicators
  • System expansion connections are provided which allows for a maximum of 8 two wire repeater panels (please note that one CFP761 network card is needed for each system)
  • IP Rating: IP30
  • Weight: 1.75kg (without any batteries)

Please note that the compatible Apollo AlarmSense detectors for these fire alarm panels can be found on this website, under the “Fire Alarm Detectors & Accessories” sub-category. This sub-category can be found under “Security & Fire Detection”

C-Tec CFP704-2 Alarmsense 4 Zone 2 Wire Fire Alarm Panel With Keypad / Keyswitch Entry

Part No: CFP704-2

The C-Tec CFP704-2 two wire four zone fire alarm panel is compatible with Apollo’s Alarmsense range of fire alarm detectors, sounders, call points, and also their visual indicators.

This panel includes four AlarmSense zones, as well as four conventional sounder circuits, a class change and alert inputs; and also an on board fault and fire relays.

Specification:

  • Mains Supply: 230 volts 50/60Hz
  • Mains Rated Current: 350mA maximum
  • Quiescent Current: 25mA
  • 1.5A compliant integral switch mode psu
  • Stylish flush or surface mountable plastic lid and enclosure, without the need for a bezel
  • LPCB (Loss Prevention Certification Board) certified to EN54 parts 2 and 4
  • Produced in the UK by C-Tec
  • Room for two 3.2Ah VRLA batteries
  • Multiple indicators
  • System expansion connections are provided which allows for a maximum of 8 two wire repeater panels (please note that one CFP761 network card is needed for each system)
  • IP Rating: IP30
  • Weight: 1.75kg (without any batteries)

Please note that the compatible Apollo AlarmSense detectors for these fire alarm panels can be found on this website, under the “Fire Alarm Detectors & Accessories” sub-category. This sub-category can be found under “Security & Fire Detection”

C-Tec CFP702-2 Alarmsense 2 Zone 2 Wire Fire Alarm Panel With Keypad / Keyswitch Entry

Part No: CFP702-2

The C-Tec CFP702-2 two wire two zone fire alarm panel is compatible with Apollo’s Alarmsense range of fire alarm detectors, sounders, call points, and also their visual indicators.

This panel includes two AlarmSense zones, as well as four conventional sounder circuits, a class change and alert inputs; and also an on board fault and fire relays.

Specification:

  • Mains Supply: 230 volts 50/60Hz
  • Mains Rated Current: 350mA maximum
  • Quiescent Current: 25mA
  • 1.5A compliant integral switch mode psu
  • Stylish flush or surface mountable plastic lid and enclosure, without the need for a bezel
  • LPCB (Loss Prevention Certification Board) certified to EN54 parts 2 and 4
  • Produced in the UK by C-Tec
  • Room for two 3.2Ah VRLA batteries
  • Multiple indicators
  • System expansion connections are provided which allows for a maximum of 8 two wire repeater panels (please note that one CFP761 network card is needed for each system)
  • IP Rating: IP30
  • Weight: 1.75kg (without any batteries)

Please note that the compatible Apollo AlarmSense detectors for these fire alarm panels can be found on this website, under the “Fire Alarm Detectors & Accessories” sub-category. This sub-category can be found under “Security & Fire Detection”

iKool-50 Plus Masterkool Air Cooler For A 25 Metre Square Room

Part No: iKool50 Plus

The iKool 50 is a an air cooler, which is often called a “swamp cooler” or “spot cooler,” works by using evaporation to achieve a cool environment.

Evaporative coolers are very easy to operate, have low running costs; and are portable too; which means that they can be easily moved to the area that they are required for.

Specification:

  • Coverage Area: 25 m2
  • Air Volume: 2410 m3/hr
  • Power: 125w
  • Current: 0.57A
  • Water Tank Capacity: 26 litres
  • Water Continuous Usage: 7 – 11 hours
  • Fan Speed: 4 speed
  • Dimensions: 42.7 x 36.5 x 106cm
  • Net Weight: 12kg
  • Water level sensor
  • Timer
  • Supplied with a remote control
  • Temperature Drop: 5 – 7 degrees C

iKool-25 Plus Masterkool Air Cooler For A 15 Metre Square Room

Part No: iKool25 Plus

The iKool 25 is a an air cooler, which is often called a “swamp cooler” or “spot cooler,” works by using evaporation to achieve a cool environment.

Evaporative coolers are very easy to operate, have low running costs; and are portable too; which means that they can be easily moved to the area that they are required for.

Specification:

  • Coverage Area: 15 m2
  • Air Volume: 1432 m3/hr
  • Power: 62w
  • Current: 0.29A
  • Water Tank Capacity: 13 litres
  • Water Continuous Usage: 10 – 13 hours
  • Fan Speed: 4 speed
  • Dimensions: 32 x 27 x 86cm
  • Net Weight: 8kg
  • Operating Weight: 21kg
  • Water level sensor
  • Timer
  • Supplied with a remote control
  • Temperature Drop: 5 – 7 degrees C

Ventcroft VFP-415ERH No-Burn 1.5mm 4 Core & Earth Fire Performance Cable In Red 100m Reel

Part No: VFP-415ERH

Vencroft 1.5mm 4 core & CPC earth fire alarm cable in red, supplied on a 100m drum.

This cable is flexible, and is manufactured in the UK, using all of the latest technology that is available.

No-burn is the fastest cable, when it comes to termination, as there are no annoying foils, or multiple sheaths which need stripping; which is a common experience that is faced with a lot of the other manufacturers fire alarm cable.

Please click here to view the manufacturer’s pdf specification datasheet on the No-Burn Fire Performance Cable

Ventcroft VFP-225ERH No-Burn 2.5mm 2 Core & Earth Fire Performance Cable In Red 100m Reel

Part No: VFP-225ERH

Vencroft 2.5mm 2 core & CPC earth fire alarm cable in red, supplied on a 100m drum.

This cable is flexible, and is manufactured in the UK, using all of the latest technology that is available.

No-burn is the fastest cable, when it comes to termination, as there are no annoying foils, or multiple sheaths which need stripping; which is a common experience that is faced with a lot of the other manufacturers fire alarm cable.

Please click here to view the manufacturer’s pdf specification datasheet on the No-Burn Fire Performance Cable

Ventcroft VFP-215ERH No-Burn 1.5mm 2 Core & Earth Fire Performance Cable In Red 100m Reel

Part No: VFP-215ERH

Vencroft 1.5mm 2 core & CPC earth fire alarm cable in red, supplied on a 100m drum.

This cable is flexible, and is manufactured in the UK, using all of the latest technology that is available.

No-burn is the fastest cable, when it comes to termination, as there are no annoying foils, or multiple sheaths which need stripping; which is a common experience that is faced with a lot of the other manufacturers fire alarm cable.

Please click here to view the manufacturer’s pdf specification datasheet on the No-Burn Fire Performance Cable

iKool100 Masterkool Air Cooler For A 60 Metre Square Room

Part No: iKool100

The iKool-100 is a an air cooler, which is often called a “swamp cooler” or “spot cooler,” works by using evaporation to achieve a cool environment.

Evaporative coolers are very easy to operate, have low running costs; and are portable too; which means that they can be easily moved to the area that they are required for.

Specification:

  • Coverage Area: 60 m2
  • Air Volume: 7000 m3/hr
  • Power: 320w
  • Temperature Drop: 5 – 7 degrees C
  • Voltage: 220v / 50Hz
  • Current: 2.0A
  • Water Tank Capacity: 93 litres
  • Water Continuous Usage: 10 – 17 hours
  • Fan Speed: 3 speed
  • Depth: 570mm
  • Width: 870mm
  • Height: 1380mm
  • Net Weight: 42kg
  • Noise: 62dB
  • Supplied with a remote control

iKool-10 Plus Masterkool Air Cooler For A 10 Metre Square Room

Part No: iKool10 Plus

The iKool-10 Plus is a an air cooler, which is often called a “swamp cooler” or “spot cooler,” works by using evaporation to achieve a cool environment.

Evaporative coolers are very easy to operate, have low running costs; and are portable too; which means that they can be easily moved to the area that they are required for.

 

Specification:

  • Coverage Area: 10 m2
  • Air Volume: 760 m3/hr
  • Power: 58w
  • Current: 0.26A
  • Water Tank Capacity: 9.3 litres
  • Water Continuous Usage: 10 – 13 litres/hours
  • Water Evaporation Rate: 0.7 – 0.9 litres/hour
  • Fan Speed: 3 speed
  • Vent Size: 21.5 x 25cm
  • Cooling Pad Grade: 5090
  • Number Of Cooling Pads: 1
  • Cooling Pad Volume: 2673 cm 3
  • Dimensions: 28 x 25 x 74cm
  • Net Weight: 5.5kg
  • Operating Weight: 14.8kg
  • Supplied with a remote control
  • Temperature Drop: 5 – 7 degrees C
0